Bed preparation
Weeds are pulled with their roots, and leaves, sticks and dead stems are cleared. Old mulch that has matted into a crust is broken up.

RAH Solutions LLC weeds and edges planting beds, then spreads fresh mulch 2 to 4 inches deep and keeps it off trunks, stems and siding. The crew serves Edgerton and nearby towns, with free on-site estimates.
Last updated: October 2026
RAH Solutions LLC is a licensed and insured, family-owned landscaper based in Edgerton, Wisconsin. Started by Robert Harried in 2023, it serves Rock and Dane County homes and businesses.
RAH Solutions LLC prepares the bed before any mulch goes down: weeds pulled, leaves and sticks cleared, and the edge cut or set. Mulch is then spread to an even 2 to 4 inches, pulled back from trunks and stems, and the lawn and hard surfaces are cleaned up. Estimates are free.
Mulch does three jobs. It shades the soil so fewer weed seeds sprout. It slows evaporation, so beds need less watering in July. And it evens out soil temperature, which matters in a climate where the ground freezes and thaws many times each winter.
Most calls for mulching near me in Edgerton come in spring, when last year’s layer has faded and thinned and weeds are starting. Fresh mulch on top of weeds does not fix that. The weeds grow through within weeks. That is why the visit starts with bed preparation and why the estimate lists it separately from the mulch itself.
Mulching is often the last step of a larger job. It follows a spring yard cleanup, or it finishes a new bed built under landscape installation. It can also be booked on its own.
RAH Solutions LLC mulches home and commercial planting beds around Edgerton, and does the preparation that makes the mulch work.
Weeds are pulled with their roots, and leaves, sticks and dead stems are cleared. Old mulch that has matted into a crust is broken up.
A fresh spade-cut edge or installed edging gives the mulch something to stop against, so it stays in the bed and the grass stays out.
The usual choice for planted beds. Shredded hardwood and bark knit together and stay put on a slope, in natural or dyed colors.
A flat ring of mulch around a tree keeps mowers and string trimmers away from the bark. It is spread wide and kept off the trunk.
Stone does not break down or need a yearly top-up. It suits foundation strips, drip lines and beds beside a driveway more than beds full of perennials.
Entrance beds, sign plantings and parking lot islands at businesses, refreshed so the front of the property looks cared for.
Mulch belongs 2 to 4 inches deep, and it can be spread whenever the ground is not frozen. RAH Solutions LLC checks four things on every bed.
The 2 to 4 inches includes what is already in the bed. A bed that still has an inch or two only needs a thin layer on top.
Mulch is pulled back from tree trunks, shrub stems and perennial crowns. Piled against bark, it holds moisture where the plant needs to stay dry.
Many local yards have silt loam over clay that drains slowly. In beds that stay wet, mulch goes on thinner so the soil can dry between rains.
Spring mulch works best after cleanup and once the soil has begun to warm. Fall mulch protects new plantings through winter freezing and thawing.
RAH Solutions measures every bed during the estimate, but the rule is simple. One cubic yard of mulch covers about 108 square feet at 3 inches deep. Multiply the length of a bed by its width to get square feet, then divide by 108.
A bed 30 feet long and 6 feet wide is 180 square feet, which takes a little under two cubic yards for a full new layer. A top-up over existing mulch takes less. The how much mulch do I need guide covers curved beds, tree rings and bags versus bulk.
RAH Solutions LLC follows the same four steps on one front bed and on a whole property.
Robert walks the beds, measures them, checks how much old mulch is there and looks at the edges.
You receive a written estimate that lists the bed prep, any edging and the amount and type of mulch.
Beds are weeded, debris is cleared, edges are cut or edging is set, and mulch is spread to an even depth.
Mulch is pulled back from trunks, stems and siding, walks and drives are blown off, and Robert walks the beds with you.
These are RAH Solutions job photos: a long bed with mulch down and the edge set, and a perennial bed with edging laid out before the mulch goes on.


Describe the beds on a call to (608) 501-5123 and Robert will tell you what to expect.
Two to four inches. Less than two inches lets light through and weeds come up. More than four inches can keep water and air from reaching roots. Beds that already hold some mulch only need enough to bring them back into that range.
Wood mulch breaks down and fades, so most beds get a top-up every year or two. You rarely need to remove the old layer. If it has matted into a crust, it is loosened first so water can get through.
Mid to late spring is the usual time, after beds are cleaned up and the soil has started to warm. Mulch can go down any time the ground is not frozen. A fall layer protects the roots of new plantings from freezing and thawing.
It stops most of them. A layer two to four inches deep blocks the light weed seeds need. Weeds that are already growing must be pulled first, and a few will still seed into the top of the mulch. Garden maintenance visits keep those from spreading.
Measure each bed in square feet. One cubic yard covers about 108 square feet at three inches deep. The mulch guide shows the math, and RAH Solutions measures the beds during the estimate so you do not have to.
Yes. Mulch heaped against a trunk, often called a mulch volcano, holds moisture on the bark and invites rot and rodents. Mulch around a tree should be a flat ring pulled back a few inches so the base of the trunk stays visible.
Tell RAH Solutions what the yard, lot or driveway needs. Robert looks at the property in person and sends a written estimate, with no pressure and no obligation.
or call (608) 501-5123